K20A Engine Part ID Pics

[Karlo]

K20A Engine Part ID "Work in Progress"
From Fuster Cluck on K20A.org

http://i188.photobucket.com/albums/z302/landfalcon/www%20ExoCars%20net/IMG_4963_crrs42.jpg
H: Oil pressure sender
I: Crank Position Sensor
J: Part of Oil Cooler
K: Another part of Oil Cooler
L: Crank pulley
M: VTEC Solenoid
N: VTEC oil pressure sensor
Q: VTC oil control solenoid valve
W: Alternator
X: A/C compressor
Y: Water Pump
Z: Auto Tensioner Pulley
1: Auto Tensioner
2: A/C compressor harness
3: Passenger side engine mounting bracket








http://i188.photobucket.com/albums/z302/landfalcon/www%20ExoCars%20net/IMG_5796_disect_rs50.jpg

A: Coolant outlet /inlet to heater
B: Vehicle Speed Sensor, or VSS
C: Clutch line
D: Tranny ground
E: Main engine harness
F: Oil Filter
G: Coolant drain bolt
H: Oil pressure sender
I: Crank Position Sensor
J: Part of Oil Cooler
K: Another part of Oil Cooler
L: Crank pulley
M: Vtec Solenoid
N: VTEC oil pressure sensor
O: Looks to be part of the manifold vacuum that would go to the brake booster
P: Evap control valve hardline. Most people remove both of those hardlines
Q: VTC oil control solenoid valve
R: Vin plate
S: Exhaust manifold heat shield
T: Header
U: Charge harness
V: Tranny bracket
W: Alternator
X: A/C compressor
Y: Water Pump
Z: Auto Tensioner Pulley
1: Auto Tensioner
2: A/C compressor harness
3: Passenger side engine mounting bracketX:
4: Charge harness
5: Intake manifold
6: Coolant entrance or exit?
7:
8:
9: Battery ground
10:
11: Starter?
12:
13: Power Harness for Alternator
14:
15:
16:
17:
18:
19:
20:
21:
22:
23:
24: Shifter Cables connection
25: Front transmission mount bolt (not used in swap)
26: Front transmission mount bolt (not used in swap)
27: Front transmission mount bolt (not used in swap)
28:
29:
30:
31: Throttle body (opening for air intake)
32: Coolant line (feed/return?)
33: One way to fill transmission but not recommended as it takes forever. Possibly a vent to relieve pressure.
34: Driver's-side transmission mount bolt
35:
36: Intake air temperature sensor
37:
38:
39:
40:
41: Fuel rail
42: Fuel injector wiring loom
43: Injector #1
44: Injector #2
45: Injector #3
46: Injector #4
47: Engine oil filler cap
48: Engine oil dipstick


http://i188.photobucket.com/albums/z302/landfalcon/www%20ExoCars%20net/IMG_5796_topleft_rs67.jpg

http://i188.photobucket.com/albums/z302/landfalcon/www%20ExoCars%20net/IMG_5796_topright_rs67.jpg

[Karlo]

Entire rear shot:

http://i188.photobucket.com/albums/z302/landfalcon/www%20ExoCars%20net/IMG_5003_rs42.jpg

Entire rear shot:

A: Coolant outlet /inlet to heater
B: Vehicle Speed Sensor, or VSS
C: Clutch line
D: Tranny ground
E: Main engine harness
F: Oil Filter
G: Coolant drain bolt
H: Oil pressure sender
I: Crank Position Sensor
J: Part of Oil Cooler
K: Another part of Oil Cooler
L: Crank pulley
M: Vtec Solenoid
N: VTEC oil pressure sensor
O: Looks to be part of the manifold vacuum that would go to the brake booster
P: Evap control valve hardline. Most people remove both of those hardlines
Q: VTC oil control solenoid valve
R: Vin plate
S: Exhaust manifold heat shield
T: Header
U: Charge harness
V: Tranny bracket